Thermal Imaging for Quality Inspection
Engineering

Thermal Imaging for Quality Inspection

A thermal camera sees differences of hundredths of a degree but reports absolute temperature to within a few degrees. Inspection works when the decision is built on that difference.

Short answer

A thermal camera is useful in quality inspection when a defect shows up as a temperature difference at the surface: an incomplete heat seal, an overheating connection, missing hot-melt glue or uneven cooling of a moulded part. It sees only the radiation leaving the surface, so do not use its reading for accept or reject decisions until emissivity, reflections, measurement timing and pixels on target are under control.

What does a thermal camera measure in quality inspection?

A thermal camera measures the infrared radiation coming from a surface and estimates surface temperature from it. It is useful in quality inspection wherever a defect shows up as a temperature difference at the surface: heat-sealed packaging, hot-melt glue, energised electrical connections, parts fresh out of a mould. The camera does not see inside the part; it sees only the radiation leaving the surface, which is the surface's own emission and whatever it reflects from its surroundings, combined.

Separating the camera's strength from its limit is the first design step. The product page of the FLIR A50/A70, a typical camera sold for automation, shows it well: its uncooled microbolometer detector, working in the 7.5–14 µm range, has a thermal sensitivity below 35 mK, while its absolute accuracy is ±2 °C or ±2% of reading, for ambient temperatures of 15–35 °C and objects above 0 °C. In other words, the camera can tell apart differences of a few hundredths of a degree but states absolute temperature with an uncertainty of a few degrees. That is why the quality decision should rest, as far as possible, on differences within the same image.

Which defects can a thermal camera detect?

A thermal camera helps when a reliable temperature difference exists between defective and good parts at the moment of measurement. If there is no such difference, or it does not reach the surface, a better camera will not change that.

ApplicationThermal signatureWhen to measureWatch out for
Heat-sealed pouches, trays and blistersAn unbroken warm band along the seal; a gap or cold area points to a missing sealA fixed time after the sealing stationFilm reflections, cooling rate, product residue on the seal
Hot-melt glue on cartonsPresence, position and continuity of glue linesRight after applicationGlue cools quickly; timing is critical
End-of-line electrical testA hot spot when powered (loose connection, faulty solder joint, heating element)Under a defined load, after a defined timeThe product must be powered safely during the test
Moulded plastic and cast partsAn irregular cooling patternAt ejection from the mouldSmall cycle-time differences change the pattern
Print, colour, surface scratchesUsually noneNot suitableA visible-light camera fits better

The appeal of thermal seal inspection is that it checks every pack rather than a sample. The Sterile Barrier Association's article on heat seal inspection with IR cameras reports that this inspection runs online, allows every single package to be inspected without damaging it, and, depending on the material, can also reveal contamination and other damage to seals. Whether it can replace your existing, validated seal strength tests is a separate validation decision; make it together with your quality team.

How do emissivity and reflections distort the measurement?

Emissivity is how efficiently a surface radiates, on a scale from 0 to 1. FLIR's emissivity guide gives practical values: highly polished metals such as copper or aluminium usually have an emissivity below 0.10; roughened or oxidised metals 0.6 or more; flat-finish paints about 0.90; human skin and water about 0.98. Shiny surfaces behave like mirrors and reflect radiation from hot objects nearby. According to the guide, if the target's emissivity is below 0.5 you are unlikely to get an accurate temperature measurement.

The meaning on the line is clear. On metallised film, an aluminium foil lid or a shiny metal part, the "hot area" the camera sees may be a reflection of the sealing jaw, a heater, a lamp or an operator. Fix the camera angle, move hot sources out of the reflection path of the field of view or shield them, and validate the measurement again whenever the surface type changes. During calibration, sticking a tape of high, known emissivity on one point of the surface and comparing readings against it is a practical method the guide also suggests.

How many pixels do you need on the target?

An accurate temperature reading needs the target to fill more than one pixel. FLIR's guide to measuring distance states that when measuring temperature with a thermal camera you want at least 3 × 3 pixels on the target; do not base an accept or reject decision on a single-pixel reading.

Hypothetical calculation: if your seal band is 5 mm wide, putting at least three pixels across it needs at most about 1.67 mm per pixel. At a horizontal resolution of 640 pixels, that means the camera's field of view can be at most about 1.07 m wide across the line; with a 464-pixel detector the limit drops to about 0.77 m. If several lanes run side by side on the belt, this calculation directly decides how many cameras you need.

Why do measurement timing and line speed matter?

A thermal signature fades. As the part cools after sealing or gluing, the difference between good and defective areas shrinks. So measure after a fixed delay, and define the delay by position rather than time: when the line speeds up or slows down, the same distance corresponds to a different cooling time. Take the trigger from an encoder and record line speed with every measurement. The product's incoming temperature varies too: a tray arriving from cold storage and one at room temperature look different after the same seal. If you can measure incoming temperature, add it to the record.

Motion creates a second problem. A study by Srinivasan Ramanagopal and colleagues, published at Robotics: Science and Systems 2020, shows that uncooled microbolometers suffer from significant motion blur, caused by the thermal inertia of each pixel. On a fast line, a narrow seal band can blur and the temperature difference can spread. Before installation, capture at real line speed, measure how far the edges of the band spread, and if necessary move the measurement to a point where the part slows down or stops.

How do you set the decision rule?

Do not look for a universal temperature threshold. Base the decision on differences within the same image: the seal band's temperature difference from a reference area on the same part, breaks in the profile taken along the band, and the length and position of a break. This approach largely compensates for changes in ambient temperature and in the product's incoming temperature, and it relies on the camera's thermal sensitivity rather than its absolute accuracy.

Derive the limits from measured process variation. Measure known-good parts and defective parts confirmed by the quality team across shifts, products and line speeds, and set the pass, inspect and reject bands from those distributions. Route borderline parts to human review instead of forcing them through a single sharp threshold.

How do you validate a thermal station before go-live?

Calibration shows that the camera reads correctly; validation shows that the station decides correctly. They are separate jobs. During the shadow run, compare the station's decisions with technician checks and keep three counts separately by shift and product: missed defects, needless rejects and unmeasurable frames. To see whether the thermal decision really reflects seal quality, regularly pull samples from both flagged and passed packs and compare them with your existing destructive seal test. If you test only flagged packs, you will never see the defects that escape. Track the unmeasurable-frame rate as a quality indicator too; a sudden rise can point to a change in the camera, the lens or the station's surroundings.

A thermal calibration checklist

CheckWhat to doWhen
Reference readingPlace a reference of known temperature next to the measurement area and log its reading; stop automatic rejection if the deviation exceeds the site toleranceStart of shift and after maintenance
Surface cardRecord the material, surface finish, viewing angle, distance and emissivity setting for the stationAt installation and when the material changes
Reflection checkCapture a cold part; any area that looks warm on a cold part is a reflectionAt installation and when the station's surroundings change
Pixel count and focusConfirm that at least 3 × 3 pixels fall on the narrowest measurement area and that focus is sharpAt installation and when the lens or mounting changes
Measurement delayRecord the distance between the process step and the image, and the line speedEvery measurement
Ambient conditionsRecord ambient temperature and airflow at the stationContinuously
Known samplesRun one confirmed good and one confirmed defective sample per product and log the resultStart of shift
Shadow runBefore connecting the reject gate, run a period that only logs decisions, and compare them with technician checksBefore go-live and after major changes
RevalidationRerun the whole list when the lens, mounting, film, line speed or sealing temperature changesOn change

Hypothetical example: incomplete seals on tray lids

On a food line, a film lid is heat-sealed onto plastic trays. The thermal camera sits a fixed distance after the sealing station, placed so that the 6 mm seal band covers four pixels across in the image. The decision rule rests on the band's temperature difference from a reference area at the tray's edge and on the length of breaks in the profile along the band. During the trial week, the quality team prepares trays with product residue deliberately left on the seal band and compares their thermal images with confirmed good trays.

In the second week, a product with a metallised lid film enters the line, and the camera starts seeing a reflection of the sealing jaw on good trays as well. This product needs its own station card, a different viewing angle and newly set decision bands; until then it is inspected manually.

Common mistakes

  • Treating a bright pixel as proof of a defect.
  • Deciding on an absolute temperature threshold instead of differences within the same image.
  • Entering the emissivity setting once and not updating it when the material changes.
  • Not calculating how many pixels fall on the target.
  • Assuming measurement timing is independent of line speed.
  • Not testing motion blur at real line speed before installation.

Whether the camera is thermal or visible-light, the general steps of acceptance testing, line integration and monitoring after go-live are the same; we describe those steps on our visual quality inspection service page.

Key takeaways

  • Use thermal imaging only where the defect creates a reliable temperature difference at the surface at the moment of measurement.
  • Base decisions on differences within the same image, not on an absolute temperature threshold.
  • Shiny and metallised surfaces reflect heat; fix the viewing angle, shield hot sources and check a cold part for reflections.
  • Put at least 3 × 3 pixels on the narrowest area you measure, and size the field of view from that.
  • Trigger by position from an encoder, record line speed and test motion blur at real speed before installation.

Frequently asked questions

Can a thermal camera inspect heat seals on every pack?

Yes, that is its main appeal: it checks seals online without damaging the pack, instead of relying on samples. It works when a missing or contaminated seal leaves a measurably different heat pattern at a fixed time after sealing; validate that on your own film and line speed first.

Why does a thermal camera show the wrong temperature on shiny metal?

Polished metals have very low emissivity and act like mirrors, so the camera sees heat reflected from nearby sources rather than the part itself. FLIR notes that below an emissivity of about 0.5 an accurate reading is unlikely; use a high-emissivity reference tape or measure differences instead.

How accurate are industrial thermal cameras?

They are far better at relative than absolute measurement. A typical automation camera such as the FLIR A50/A70 resolves differences below 35 mK but specifies absolute accuracy of ±2 °C or ±2% of reading under defined conditions.

Do I need a cooled thermal camera for a fast line?

Not necessarily, but test first. Uncooled microbolometers blur moving objects because of each pixel's thermal inertia. Capture at real line speed, measure how much a narrow feature spreads, and consider measuring where the part slows down before changing the camera type.

Can a thermal camera replace a visible-light camera?

Only for defects that create a temperature difference. Print, colour and most surface scratches have no thermal signature and are better inspected with a visible-light camera; some stations use both.

All articles